Edimax AR-7286WnA Manuale Utente

1 AR-7286WnA / AR-7286WnB User Manual 6-2013 / v1.0

10 2. Hardware Installation 1. Connect the ADSL line. Connect the line port of the router of the device to the modem interface of a splitter using

11 3. Connect the power adapter to the router. Plug one end of the power adapter into a wall outlet and connect the other end to the 12V interface

12 Configuration 2 0 shows the correct connection when a telephone set is installed before the splitter. Figure 2 - Connection diagram (Connectin

13 5. Firewall settings. Please turn off all personal firewalls before you continue the setup – firewalls can block communication between your PC a

14 3. Locate the “Network Connections” icon and double-click to open network connection settings. 4. Select the “Local Area Connection” icon a

15 5. Select “Internet Protocol (TCP/IP)” and then click “Properties” 6. Ensure that “Obtain an IP address automatically” and “Obtain DNS serv

16

17 3. IP Address Setting To use the router to access the Internet, the PCs in the network must have an Ethernet adapter installed and be connected

18 2. Click the Network icon and then select Open Network and Sharing Center to open the Network and Sharing Center window. 3. Click Ethernet

19 4. Check your list of Network Components. Select Internet Protocol Version 4 (TCP/IPv4) and click the Properties button. 5. In the Internet

2 COPYRIGHT Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed

20 6. Click OK (shown above) to confirm the setting. Your PC will now obtain an IP address automatically from your router’s DHCP server. Note: Pl

21 4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select Obtain an IP address automatically and Obtain DNS server address auto

22 3. Check your list of Network Components. You should see Internet Protocol Version 4 (TCP/IPv4) on your list. Select it and click the Properties

23 3. Check your list of Network Components. You should see Internet Protocol [TCP/IP] on your list. Select it and click the Properties button. 4.

24 4. EZmax Setup Wizard You can configure the router by running the setup wizard on the CD-ROM included in the package contents. The wizard enabl

25 2. Please select your product.

26 3. Please ensure all hardware is correctly installed. Check the box and click “Next”.

27 4. Select your country and ISP. If your ISP is not listed, select “Other” from the list and refer to 4.2. Internet Connection Type. 5. Enter

28 6. Please wait while the router connects to the Internet. When the router is connected successfully, you will see the screen below.

29 4.2. Internet Connection Type If your country or ISP is not listed, please select “Other” from the list.

3 Contents 1. PRODUCT INTRODUCTION ...

30 Then select your Internet connection type and click “Next”. If you are not sure, please contact your Internet Service Provider (ISP). Depend

31 Static IP Address Uses a static IP address. Your service provider gives a static IP address to access Internet services. 4.2.1. PPoE/PPPoA

32 between two points in an ATM network. Its valid value is in the range of 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). E

33 VCI Virtual channel identifier (VCI) is the virtual channel between two points in an ATM network. Its valid value is in the range of 32 to 65535

34 default, VPI is set to 8. VCI Virtual channel identifier (VCI) is the virtual channel between two points in an ATM network. Its valid value is

35 valid value is in the range of 0 to 255. Enter the correct VPI provided by your ISP. By default, VPI is set to 8. VCI Virtual channel identifie

36

37 5. Web Configuration The router can also be configured using the web-based configuration interface. Follow the instructions below. 5.1. Access

38 5.2.2. System Log Choose Status > System Log, the page shown in the following figure appears. In this page, you can view, clear or save the

39 5.2.3. Statistics Choose Status > Statistics. The Statistics page that is displayed contains Ethernet Statistics, ADSL Statistics a

4 5.4.3. Wireless ...

40 5.2.3.1. WLAN Statistics In the Traffic Statistic page, click WLAN and the page shown in the following figure appears. In this page, you c

41 1. Click RUN WIZARD, there will pop up a new page as shown in the following figure appears. 2. Click EXIT, this page will be cl

42 In this page, enter a new password for the admin account. After finishing all quick start settings, it will be saved and effect immediately. 3. C

43 The following table describes the parameters in this page: Field Description Country Select the country you are in. ISP Select your Internet Se

44 The following table describes the parameters in this page: Field Description VPI Virtual path identifier (VPI) is the virtual path betwee

45 Field Description two points in an ATM network. Its valid value is between 1 and 65535. Enter the correct VCI provided by your ISP. C

46 Field Description Mask ISP Gateway Enter the default gateway provided by your ISP. Connection Type You can select LLC or VC-Mux. In this example,

47 Field Description Type encapsulation mode is set to PPPoE LLC. After setting, click NEXT, the page as shown in the following figure appears.

48 The following table describes the parameters of this page: Field Description Virtual Circuit Select a virtual circuit from the drop-list

49 Field Description PCR Peak cell rate (PCR) is the maximum rate at which cells can be transmitted along a connection in the ATM network.

5 1. Product Introduction 1.1. Package Contents Before you start using this product, please check if there is anything missing in the package and c

50 The following table describes the parameters of this page: Field Description IP Common Options Encapsulation You can choose 1483 Bridged IP LLC,

51 Field Description IGMP version 1 (IGMP v1) and IGMP version 2 (IGMP v2). Select Disabled to disable it. IPv6 Address DHCP IPv6 Enable Provide ad

52 The following table describes the parameters of this page: Field Description IP Common Options Encapsulation You can choose 1483 Bridged IP LLC

53 Field Description Gateway You can enter the gate way IP for dial-up, which is provided by your ISP. NAT Select whether to enable Ne

54 connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. T

55 Field Description Connection Setting Connection You can choose Always On (Recommended), Connect On-Demand or Connect Manually. TCP MSS Optio

56 Field Description Enable DHCP in local pools. Choose DHCP or SLAAC. DHCP PD Enable IPv6 Prefix Delegation Options for DHCPv6. You may enable or d

57 After finishing, click SAVE to apply the settings of this PVC. 5.4.2. LAN Choose Interface Setup > LAN. The LAN page that is displ

58 Field Description Mask subnet mask is from 255.255.0.0 to 255.255.255.254. Alias IP Address You may enter the second IP Address. Alias Subnet Mas

59 Field Description Auto Discovered, the router accepts the firstly-received DNS assignment from one of the PPPoA, PPPoE or MER enabled PVC(s) duri

6  Do not put this device close to heat sources or high temperatures. Keep the device out of direct sunshine.  Do not put this device close to a p

60 In the DHCP field, choose DHCP Relay, the page shown in the following figure appears. Enter a server IP address running on WAN side.

61 5.4.3. Wireless Choose Interface Setup > Wireless. The page as shown in the following figure appears. The Wireless page conta

62 Field Description power levels within these frequency ranges. The default is 2. Beacon Interval Beacon Interval range is from 20 to 1000. R

63 Field Description wireless client searches. Use WPS WPS technology allows new customers without a previously-established account to secu

64 5.5.1. Firewall Choose Advanced Setup > Firewall. The page shown in the following figure appears. You can select this option to automatically

65 The following table describes the parameters and buttons of this page: Field Description Destination IP Address Enter the IP address of the desti

66 Field Description Number of IPs This field is to specify how many IPs are provided by your ISP for the current VC. You can select Single

67 The following table describes the parameters of this page: Field Description DMZ Select Enabled or Disabled to enable this function. DMZ Host IP

68 Field Description Application You can enter an application name, or select a name from the right drop-list menu like FTP or TELNET. Protocol Cho

69 The following table describes the parameters of this page: Field Description Rule Index The Virtual server rule index for this VC. You can specif

7 Internet Green On Internet connected in router mode Flashing Internet activity (transferring/receiving data) in router mode. Off Device in bridged

70 The following table describes the parameters of this page: Field Description Quality of Service IP Version In this example, the IP version is s

71 Field Description MGCP, SNMP, DNS, DHCP, RIP, RSTP, RTCP and RTP. Physical Ports Choose an Ethernet interface or WLAN Interface. Destination MAC

72 Field Description video and voice. Data classes four through one range from controlled-load applications such as streaming multimedia and busines

73 The following table describes the parameters of this page: Field Description Quality of Service IP Version Select IP version. In this exam

74 Click Save at the bottom of the page to save the discipline. To view the rules and actions, click QoS Settings Summary to enter the page shown in

75 Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with

76 The following table describes the parameters of this page: Field Description VLAN Index Choose a VLAN index from 1 to 8. Active Select Yes or N

77 The router supports these modulations: G.Lite, T1.413, G.DMT, ADSL2, ADSL2+ and Auto-Syno Up. The router negotiates the modulat

78 The following table describes the parameters and buttons of this page: Field Description ACL Rule Index You can establish sixteen ACL rules at

79 The following table describes the parameters and buttons of this page: Field Description Filter Type Selection Support IP / MAC Filter, Applica

8 Rear Panel Item Description Power On/Off Button Switches the router on or off. Power Power port for included 12V power adapter. Wireless On/Off

80 5.6.2.2. Application Filter Choose Access Management > Filter, select Application Filter from the drop-down list Filter Type Selection, and

81 The following table describes the parameters and buttons of this page: Field Description Active Make URL Filter rule activated or deactivated.

82 The following table describes the parameters of this page: Field Description Get Community Select to set the password for the incoming G

83 5.6.5. DDNS Choose Access Management > DDNS, the page shown in the following figure appears. The Dynamic Domain Name System (DDNS) lets you u

84 The following table describes the parameters of this page: Field Description URL URL for the CPE to connect to the ACS using the CPE

85 5.7. Maintenance In the navigation bar, click Maintenance. The Maintenance page that is displayed contains Administration, Time Zon

86 The following table describes the parameters of this page: Field Description Synchronize time with You can choose NTP Server automatically

87 The following table describes the parameters of this page: Field Description New Firmware Location Click Browse to select the firmware file. Ro

88 5.7.5. Diagnostics Choose Maintenance > Diagnositics, the page shown in the following figure appears. The page shows the test results for the

89 6. Trouble Shooting Question Answer Why are all the indicators off?  Check the connection between the power adapter and the power socket. 

9 1.5. Features The device supports the following features:  Various line modes  External PPPoE dial-up access  Internal PPPoE/PPPoA dial-up acc

90 EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directiv

91 Declaration of Conformity We, Edimax Technology Co., LTD., declare under our sole responsibility, that the equipment described below complies

92